Gracias por responder.
Si los he visto todos, pero el gran problema es que en alguno no ponen los archivos que hay que tener en la SD, otros usan un cable que yo no tengo, como es el de serial. Y en el otro no se ve bien lo que pone, aún así creo que esta mejor explicado en la página openzipit, pero la forma que explica ahí no me funciona, al menos la única que puedo hacer que es la de wifi.
Seguiré probando a ver. Si alguien encontrara un manual de instalación por microSD explicado en texto se lo agradecería.
Voy muy perdido, estoy probando de dos maneras y ninguna de ellas lelga a hacer anda.
-Primero he intentado hacerlo por ad-hoc, clavandole al bicho los archivos necesarios, pero ni siquiera me deja conectar con el zipit al ad-hoc.
-Luego he intentado que bootee un pequeño linux puesto en la microSD pero la verdad, he puesto unos cuantos archivos que he visto pero ninguno ha echo que booteara, simplemente lee la tarjeta pero sigue con el sistema operativo original sin hacer nada.
Lo mas seguro es que este haciendo algo mal.
Creeis que pudiera ser que los archivos que pongo en la tarjeta sd deverían estar instalados de alguna forma, estilo un usb booteable?
Cualquier ayuda se aprecia.
Bueno. Seguí un tutorial y me he quedado atasacado en un punto en que creo que ya se me ha flasheado mal el zipit.
Me explico, He seguido los pasos de esta página
http://quantumlime.com/zipitY hiba todo bien hasta que arrancó el Openzipit, que se me quedo colgado y no pasa de ahí. He probado todas las combinaciones de encenderlo pero nada (con la tarjeta sd, sin, con la luz, con la bateria,...)
Me quede en este paso:
1. First, flash the zipit. Extract the autoflasher bundle to a fat16 formatted memory card
2. Open Aliosa27’s wireless+x+audio.tar.gz file, and copy out the /boot/linux-2.6.29 file to your memory card
3. Rename this file kernel.bin
4. Boot the zipit with the SD card inserted. If this does not start the linux flash, go to settings->reset to default and it should soft-reset
5. Some SD cards are reported to not work, or not always be seen by the zipit. Try both with and without the power cable plugged in
6. The z2 will boot linux and copy the wifi firmware to the sd card before flashing linux to the Z2.
7. Copy off the 2 wireless firmware files gspsi.bin and gpspsi_helper.bin to a folder, you will copy these back to the memory card after we write the image
8. IMPORTANT — rename helper_gspi.bin to be gspi8686_hlp.bin or it will not load later!
9. Extract the 1/2gb image to a folder
10. Extract phsydiskwrite to a folder
11. Insert your microSD card into the computer (adapter, usb stick, etc)
12. Run phsygui.exe from within the folder you extracted psydiskwrite to (requires .net framework)
13. right-click on the drive letter for your SD card, select the first menu item, and then select the 1/2gb image you extracted earlier (.img)
14. After it writes, safely remove the disk then plug it back in. if windows can see the fat partition copy the firmware files to it
15. If windows cannot see this fat partition, dowload the ext2 filesystem driver, run it, then copy the firmware files over to /lib/firmware/notlibertas/ (yes notlibertas, the fat filesystem is mounted as /lib/firmware/libertas so you can’t use that)
16. Insert the sd card into the Z2, and boot. Login as root, password debian. Congrats! You’ve got debian on the zipit!
17. If windows couldn’t see your fat32 partition, copy the firmware files from /lib/firmware/notlibertas to /lib/firmware/libertas. You may need to run fsck if linux can’t see the files.
18. Reboot, and you should have wireless device when you type iwconfig. Configure the wireless settings, and you’re ready.
No es fácil encontrar información sobre esto, pero aún menos de problemas que surgen mientras se instala. No se si ya me tocará flashear con los chips o que. Por cierto, pude ver la versión del firmware original y no era el 2.01 era el 1.13 o por ahí, así que eso no puede ser.
Cualquier ayuda...