elhacker.net cabecera Bienvenido(a), Visitante. Por favor Ingresar o Registrarse
¿Perdiste tu email de activación?.

 

 


Tema destacado: Tutorial básico de Quickjs


+  Foro de elhacker.net
|-+  Sistemas Operativos
| |-+  GNU/Linux (Moderador: MinusFour)
| | |-+  Efectos visuales de ubuntu cuelgan al sistema
0 Usuarios y 1 Visitante están viendo este tema.
Páginas: [1] 2 3 4 5 Ir Abajo Respuesta Imprimir
Autor Tema: Efectos visuales de ubuntu cuelgan al sistema  (Leído 16,725 veces)
nico56

Desconectado Desconectado

Mensajes: 246


Ver Perfil
Efectos visuales de ubuntu cuelgan al sistema
« en: 15 Julio 2010, 01:08 am »

Hola que tal, cuando activo los efectos visuales de ubuntu 10.04 lts, el sistema se tilda a los 3 minutos sin razon alguna :S . Que puede ser?

Mi pc es:

Intel Celeron 1.8 Ghz
Memo ram 1 GB
Memo video on-board 64 mb

Les aclaro que una vez probe el ubuntu 8.04 y los efectos visuales los hacia sin problemas.


En línea

Fitoschido

Desconectado Desconectado

Mensajes: 248



Ver Perfil WWW
Re: Efectos visuales de ubuntu cuelgan al sistema
« Respuesta #1 en: 15 Julio 2010, 05:29 am »

Qué raro, a mi me andan sin problemas, y eso que tengo un Atom N270 y 1 GB de RAM :D


En línea

El que sabe hace, el que no enseña


Miembro oficial del proyecto Ubuntu, traductor de LibreOffice/Ubuntu/Xfce/Gnome.
xexio

Desconectado Desconectado

Mensajes: 209



Ver Perfil
Re: Efectos visuales de ubuntu cuelgan al sistema
« Respuesta #2 en: 15 Julio 2010, 15:35 pm »

que gráfica tienes, haz un lspci | grep VGA en el terminal y pega aquí el resultado
En línea


nico56

Desconectado Desconectado

Mensajes: 246


Ver Perfil
Re: Efectos visuales de ubuntu cuelgan al sistema
« Respuesta #3 en: 15 Julio 2010, 22:56 pm »

Aqui esta el resultado de ese comando xexio:


00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02)
En línea

xexio

Desconectado Desconectado

Mensajes: 209



Ver Perfil
Re: Efectos visuales de ubuntu cuelgan al sistema
« Respuesta #4 en: 16 Julio 2010, 03:42 am »

prueba a generar un Xorg.conf automaticamente
con las X desactivadas
Xorg -configure

de todas formas con 64MB y encima intregrada en la placa.....
En línea


nico56

Desconectado Desconectado

Mensajes: 246


Ver Perfil
Re: Efectos visuales de ubuntu cuelgan al sistema
« Respuesta #5 en: 17 Julio 2010, 01:13 am »

prueba a generar un Xorg.conf automaticamente
con las X desactivadas
Xorg -configure

de todas formas con 64MB y encima intregrada en la placa.....

hay q ejecutar un comando ?
En línea

rastanthology

Desconectado Desconectado

Mensajes: 130


Ver Perfil
Re: Efectos visuales de ubuntu cuelgan al sistema
« Respuesta #6 en: 18 Julio 2010, 02:41 am »

si... tocas control+alt+f1 para abrir la terminal en otro tty, una vez ahi te logueas, entras en modo root haciendo sudo -i

despues haces escribis:

/etc/init.d/gdm stop
Xorg -configure

ahi se te genera el nuevo xorg, para volver a iniciar el modo grafico despues escribis

/etc/init.d/gdm start
En línea

nico56

Desconectado Desconectado

Mensajes: 246


Ver Perfil
Re: Efectos visuales de ubuntu cuelgan al sistema
« Respuesta #7 en: 18 Julio 2010, 05:45 am »

Hola, que tal, ya probe eso que me dijiste pero se volvio a colgar mal de vuelta funciona por 2 minutos y se cuelga misteriosamente.
En línea

bizco


Desconectado Desconectado

Mensajes: 698


Ver Perfil
Re: Efectos visuales de ubuntu cuelgan al sistema
« Respuesta #8 en: 18 Julio 2010, 07:35 am »

entonces puede ser algun modulo que entre con conflicto con otro, revisa con dmesg a ver si ves algo raro por ahi.
En línea

nico56

Desconectado Desconectado

Mensajes: 246


Ver Perfil
Re: Efectos visuales de ubuntu cuelgan al sistema
« Respuesta #9 en: 18 Julio 2010, 21:08 pm »

Mira ejecute ese comando "dmesg" y te pego lo que salio, no entiendo nada yo

Código:
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.32-21-generic (buildd@rothera) (gcc version 4.4.3 (Ubuntu 4.4.3-4ubuntu5) ) #32-Ubuntu SMP Fri Apr 16 08:10:02 UTC 2010 (Ubuntu 2.6.32-21.32-generic 2.6.32.11+drm33.2)
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   NSC Geode by NSC
[    0.000000]   Cyrix CyrixInstead
[    0.000000]   Centaur CentaurHauls
[    0.000000]   Transmeta GenuineTMx86
[    0.000000]   Transmeta TransmetaCPU
[    0.000000]   UMC UMC UMC UMC
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[    0.000000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000003f7c0000 (usable)
[    0.000000]  BIOS-e820: 000000003f7c0000 - 000000003f7ce000 (ACPI data)
[    0.000000]  BIOS-e820: 000000003f7ce000 - 000000003f800000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
[    0.000000] DMI present.
[    0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working around it.
[    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[    0.000000] last_pfn = 0x3f7c0 max_arch_pfn = 0x100000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-DFFFF uncachable
[    0.000000]   E0000-EFFFF write-through
[    0.000000]   F0000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask FC0000000 write-back
[    0.000000]   1 base 03F800000 mask FFF800000 uncachable
[    0.000000]   2 disabled
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] Scanning 0 areas for low memory corruption
[    0.000000] modified physical RAM map:
[    0.000000]  modified: 0000000000000000 - 0000000000010000 (reserved)
[    0.000000]  modified: 0000000000010000 - 000000000009fc00 (usable)
[    0.000000]  modified: 000000000009fc00 - 00000000000a0000 (reserved)
[    0.000000]  modified: 00000000000e0000 - 0000000000100000 (reserved)
[    0.000000]  modified: 0000000000100000 - 000000003f7c0000 (usable)
[    0.000000]  modified: 000000003f7c0000 - 000000003f7ce000 (ACPI data)
[    0.000000]  modified: 000000003f7ce000 - 000000003f800000 (ACPI NVS)
[    0.000000]  modified: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  modified: 00000000ffb80000 - 0000000100000000 (reserved)
[    0.000000] initial memory mapped : 0 - 00c00000
[    0.000000] init_memory_mapping: 0000000000000000-00000000377fe000
[    0.000000] Using x86 segment limits to approximate NX protection
[    0.000000]  0000000000 - 0000400000 page 4k
[    0.000000]  0000400000 - 0037400000 page 2M
[    0.000000]  0037400000 - 00377fe000 page 4k
[    0.000000] kernel direct mapping tables up to 377fe000 @ 10000-15000
[    0.000000] RAMDISK: 2f276000 - 2fa0f92a
[    0.000000] ACPI: RSDP 000fa170 00014 (v00 synnex)
[    0.000000] ACPI: RSDT 3f7c0000 00038 (v01 AAMMII OEMRSDTA 06000714 MSFT 00000097)
[    0.000000] ACPI: FACP 3f7c0200 00084 (v02 AAMMII OEMFACP  06000714 MSFT 00000097)
[    0.000000] ACPI: DSDT 3f7c0440 04F73 (v01  945GM   945GM2 00000002 INTL 20051117)
[    0.000000] ACPI: FACS 3f7ce000 00040
[    0.000000] ACPI: APIC 3f7c0390 0006C (v01 AAMMII OEMAPIC  06000714 MSFT 00000097)
[    0.000000] ACPI: MCFG 3f7c0400 0003C (v01 AAMMII OEMMCFG  06000714 MSFT 00000097)
[    0.000000] ACPI: OEMB 3f7ce040 00060 (v01 AAMMII AMI_OEM  06000714 MSFT 00000097)
[    0.000000] ACPI: HPET 3f7c53c0 00038 (v01 AAMMII OEMHPET  06000714 MSFT 00000097)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] 127MB HIGHMEM available.
[    0.000000] 887MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 377fe000
[    0.000000]   low ram: 0 - 377fe000
[    0.000000]   node 0 low ram: 00000000 - 377fe000
[    0.000000]   node 0 bootmap 00011000 - 00017f00
[    0.000000] (9 early reservations) ==> bootmem [0000000000 - 00377fe000]
[    0.000000]   #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
[    0.000000]   #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
[    0.000000]   #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
[    0.000000]   #3 [0000100000 - 00008d9e98]    TEXT DATA BSS ==> [0000100000 - 00008d9e98]
[    0.000000]   #4 [002f276000 - 002fa0f92a]          RAMDISK ==> [002f276000 - 002fa0f92a]
[    0.000000]   #5 [000009fc00 - 0000100000]    BIOS reserved ==> [000009fc00 - 0000100000]
[    0.000000]   #6 [00008da000 - 00008dd10b]              BRK ==> [00008da000 - 00008dd10b]
[    0.000000]   #7 [0000010000 - 0000011000]          PGTABLE ==> [0000010000 - 0000011000]
[    0.000000]   #8 [0000011000 - 0000018000]          BOOTMAP ==> [0000011000 - 0000018000]
[    0.000000] found SMP MP-table at [c00ff780] ff780
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000010 -> 0x00001000
[    0.000000]   Normal   0x00001000 -> 0x000377fe
[    0.000000]   HighMem  0x000377fe -> 0x0003f7c0
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[2] active PFN ranges
[    0.000000]     0: 0x00000010 -> 0x0000009f
[    0.000000]     0: 0x00000100 -> 0x0003f7c0
[    0.000000] On node 0 totalpages: 259919
[    0.000000] free_area_init_node: node 0, pgdat c0798720, node_mem_map c1001200
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 3951 pages, LIFO batch:0
[    0.000000]   Normal zone: 1744 pages used for memmap
[    0.000000]   Normal zone: 221486 pages, LIFO batch:31
[    0.000000]   HighMem zone: 256 pages used for memmap
[    0.000000]   HighMem zone: 32450 pages, LIFO batch:7
[    0.000000] Using APIC driver default
[    0.000000] ACPI: PM-Timer IO Port: 0x808
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
[    0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0xffffffff base: 0xfed00000
[    0.000000] SMP: Allowing 4 CPUs, 3 hotplug CPUs
[    0.000000] nr_irqs_gsi: 24
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[    0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[    0.000000] Allocating PCI resources starting at 3f800000 (gap: 3f800000:bf600000)
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:4 nr_node_ids:1
[    0.000000] PERCPU: Embedded 14 pages/cpu @c1800000 s36024 r0 d21320 u1048576
[    0.000000] pcpu-alloc: s36024 r0 d21320 u1048576 alloc=1*4194304
[    0.000000] pcpu-alloc: [0] 0 1 2 3
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 257887
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-21-generic root=UUID=21f1b113-cc50-4726-af44-536440ee7371 ro quiet splash
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] allocated 5200320 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Initializing HighMem for node 0 (000377fe:0003f7c0)
[    0.000000] Memory: 1008804k/1040128k available (4673k kernel code, 30108k reserved, 2122k data, 656k init, 130824k highmem)
[    0.000000] virtual kernel memory layout:
[    0.000000]     fixmap  : 0xfff1d000 - 0xfffff000   ( 904 kB)
[    0.000000]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[    0.000000]     vmalloc : 0xf7ffe000 - 0xff7fe000   ( 120 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xf77fe000   ( 887 MB)
[    0.000000]       .init : 0xc07a3000 - 0xc0847000   ( 656 kB)
[    0.000000]       .data : 0xc0590613 - 0xc07a2e48   (2122 kB)
[    0.000000]       .text : 0xc0100000 - 0xc0590613   (4673 kB)
[    0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.000000] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:2304 nr_irqs:440
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] hpet clockevent registered
[    0.000000] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 1795.565 MHz processor.
[    0.004005] Calibrating delay loop (skipped), value calculated using timer frequency.. 3591.13 BogoMIPS (lpj=7182260)
[    0.004026] Security Framework initialized
[    0.004047] AppArmor: AppArmor initialized
[    0.004055] Mount-cache hash table entries: 512
[    0.004207] Initializing cgroup subsys ns
[    0.004213] Initializing cgroup subsys cpuacct
[    0.004218] Initializing cgroup subsys memory
[    0.004226] Initializing cgroup subsys devices
[    0.004228] Initializing cgroup subsys freezer
[    0.004231] Initializing cgroup subsys net_cls
[    0.004254] CPU: L1 I cache: 32K, L1 D cache: 32K
[    0.004257] CPU: L2 cache: 512K
[    0.004262] mce: CPU supports 6 MCE banks
[    0.004273] CPU0: Thermal monitoring enabled (TM2)
[    0.004277] using mwait in idle threads.
[    0.004284] Performance Events: Core2 events, Intel PMU driver.
[    0.004294] ... version:                2
[    0.004296] ... bit width:              40
[    0.004297] ... generic registers:      2
[    0.004300] ... value mask:             000000ffffffffff
[    0.004302] ... max period:             000000007fffffff
[    0.004304] ... fixed-purpose events:   3
[    0.004306] ... event mask:             0000000700000003
[    0.004312] Checking 'hlt' instruction... OK.
[    0.021042] SMP alternatives: switching to UP code
[    0.029564] ACPI: Core revision 20090903
[    0.037650] ftrace: converting mcount calls to 0f 1f 44 00 00
[    0.037656] ftrace: allocating 21771 entries in 43 pages
[    0.040073] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.040386] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.080199] CPU0: Intel(R) Celeron(R) CPU          430  @ 1.80GHz stepping 01
[    0.084001] Brought up 1 CPUs
[    0.084001] Total of 1 processors activated (3591.13 BogoMIPS).
[    0.084001] CPU0 attaching NULL sched-domain.
[    0.084001] devtmpfs: initialized
[    0.084001] regulator: core version 0.5
[    0.084001] Time: 16:01:08  Date: 07/18/10
[    0.084001] NET: Registered protocol family 16
[    0.084001] EISA bus registered
[    0.084001] ACPI: bus type pci registered
[    0.084001] PCI: Found Intel Corporation 945G/GZ/P/PL Express Memory Controller Hub with MMCONFIG support.
[    0.084001] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 63
[    0.084001] PCI: Not using MMCONFIG.
[    0.084001] PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=3
[    0.084001] PCI: Using configuration type 1 for base access
[    0.084001] bio: create slab <bio-0> at 0
[    0.084001] ACPI: EC: Look up EC in DSDT
[    0.088847] ACPI: Executed 1 blocks of module-level executable AML code
[    0.094073] ACPI: Interpreter enabled
[    0.094080] ACPI: (supports S0 S1 S3 S4 S5)
[    0.094108] ACPI: Using IOAPIC for interrupt routing
[    0.106270] ACPI Warning: Incorrect checksum in table [OEMB] - 66, should be 59 (20090903/tbutils-314)
[    0.106397] ACPI: No dock devices found.
[    0.106534] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.106633] pci 0000:00:02.0: reg 10 32bit mmio: [0xfea80000-0xfeafffff]
[    0.106639] pci 0000:00:02.0: reg 14 io port: [0xdc00-0xdc07]
[    0.106645] pci 0000:00:02.0: reg 18 32bit mmio pref: [0xd0000000-0xdfffffff]
[    0.106650] pci 0000:00:02.0: reg 1c 32bit mmio: [0xfea40000-0xfea7ffff]
[    0.106731] pci 0000:00:1b.0: reg 10 64bit mmio: [0xfea38000-0xfea3bfff]
[    0.106776] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.106780] pci 0000:00:1b.0: PME# disabled
[    0.106844] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.106848] pci 0000:00:1c.0: PME# disabled
[    0.106916] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[    0.106920] pci 0000:00:1c.3: PME# disabled
[    0.106968] pci 0000:00:1d.0: reg 20 io port: [0xd880-0xd89f]
[    0.107019] pci 0000:00:1d.1: reg 20 io port: [0xd800-0xd81f]
[    0.107069] pci 0000:00:1d.2: reg 20 io port: [0xd480-0xd49f]
[    0.107120] pci 0000:00:1d.3: reg 20 io port: [0xd400-0xd41f]
[    0.107176] pci 0000:00:1d.7: reg 10 32bit mmio: [0xfea37c00-0xfea37fff]
[    0.107228] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.107233] pci 0000:00:1d.7: PME# disabled
[    0.107360] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
[    0.107365] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO
[    0.107369] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0a00 (mask 00ff)
[    0.107414] pci 0000:00:1f.1: reg 10 io port: [0x00-0x07]
[    0.107421] pci 0000:00:1f.1: reg 14 io port: [0x00-0x03]
[    0.107428] pci 0000:00:1f.1: reg 18 io port: [0x00-0x07]
[    0.107435] pci 0000:00:1f.1: reg 1c io port: [0x00-0x03]
[    0.107442] pci 0000:00:1f.1: reg 20 io port: [0xffa0-0xffaf]
[    0.107486] pci 0000:00:1f.2: reg 10 io port: [0xd080-0xd087]
[    0.107492] pci 0000:00:1f.2: reg 14 io port: [0xd000-0xd003]
[    0.107499] pci 0000:00:1f.2: reg 18 io port: [0xcc00-0xcc07]
[    0.107505] pci 0000:00:1f.2: reg 1c io port: [0xc880-0xc883]
[    0.107512] pci 0000:00:1f.2: reg 20 io port: [0xc800-0xc80f]
[    0.107537] pci 0000:00:1f.2: PME# supported from D3hot
[    0.107541] pci 0000:00:1f.2: PME# disabled
[    0.107587] pci 0000:00:1f.3: reg 20 io port: [0x400-0x41f]
[    0.107715] pci 0000:02:00.0: reg 10 io port: [0xe800-0xe8ff]
[    0.107739] pci 0000:02:00.0: reg 18 64bit mmio: [0xfebff000-0xfebfffff]
[    0.107762] pci 0000:02:00.0: reg 30 32bit mmio pref: [0xfebc0000-0xfebdffff]
[    0.107812] pci 0000:02:00.0: supports D1 D2
[    0.107814] pci 0000:02:00.0: PME# supported from D1 D2 D3hot D3cold
[    0.107820] pci 0000:02:00.0: PME# disabled
[    0.107864] pci 0000:00:1c.3: bridge io port: [0xe000-0xefff]
[    0.107869] pci 0000:00:1c.3: bridge 32bit mmio: [0xfeb00000-0xfebfffff]
[    0.107922] pci 0000:00:1e.0: transparent bridge
[    0.107945] pci_bus 0000:00: on NUMA node 0
[    0.107951] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.108096] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[    0.108209] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[    0.108275] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT]
[    0.118283] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[    0.118409] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[    0.118530] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 14 *15)
[    0.118653] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[    0.118771] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[    0.118890] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[    0.119011] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[    0.119131] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[    0.119259] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[    0.119268] vgaarb: loaded
[    0.119406] SCSI subsystem initialized
[    0.119489] libata version 3.00 loaded.
[    0.119578] usbcore: registered new interface driver usbfs
[    0.119591] usbcore: registered new interface driver hub
[    0.119623] usbcore: registered new device driver usb
[    0.119779] ACPI: WMI: Mapper loaded
[    0.119782] PCI: Using ACPI for IRQ routing
[    0.119933] NetLabel: Initializing
[    0.119936] NetLabel:  domain hash size = 128
[    0.119937] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.119949] NetLabel:  unlabeled traffic allowed by default
[    0.119993] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.120008] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[    0.124016] Switching to clocksource tsc
[    0.126180] AppArmor: AppArmor Filesystem Enabled
[    0.126204] pnp: PnP ACPI init
[    0.126225] ACPI: bus type pnp registered
[    0.134516] pnp: PnP ACPI: found 19 devices
[    0.134520] ACPI: ACPI bus type pnp unregistered
[    0.134525] PnPBIOS: Disabled by ACPI PNP
[    0.134540] system 00:01: iomem range 0xfed13000-0xfed19fff has been reserved
[    0.134550] system 00:08: ioport range 0x4d0-0x4d1 has been reserved
[    0.134553] system 00:08: ioport range 0x800-0x87f has been reserved
[    0.134556] system 00:08: ioport range 0x480-0x4bf has been reserved
[    0.134560] system 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
[    0.134563] system 00:08: iomem range 0xfed20000-0xfed8ffff has been reserved
[    0.134570] system 00:0b: iomem range 0xffc00000-0xfff7ffff has been reserved
[    0.134576] system 00:0c: iomem range 0xfec00000-0xfec00fff could not be reserved
[    0.134579] system 00:0c: iomem range 0xfee00000-0xfee00fff has been reserved
[    0.134586] system 00:0f: ioport range 0xa00-0xa0f has been reserved
[    0.134589] system 00:0f: ioport range 0xa10-0xa1f has been reserved
[    0.134592] system 00:0f: ioport range 0xa20-0xa2f has been reserved
[    0.134595] system 00:0f: ioport range 0xa30-0xa3f has been reserved
[    0.134602] system 00:11: iomem range 0xe0000000-0xe3ffffff has been reserved
[    0.134608] system 00:12: iomem range 0x0-0x9ffff could not be reserved
[    0.134611] system 00:12: iomem range 0xc0000-0xcffff could not be reserved
[    0.134614] system 00:12: iomem range 0xe0000-0xfffff could not be reserved
[    0.134617] system 00:12: iomem range 0x100000-0x3f7fffff could not be reserved
[    0.169343] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:01
[    0.169348] pci 0000:00:1c.0:   IO window: 0x1000-0x1fff
[    0.169353] pci 0000:00:1c.0:   MEM window: 0x40000000-0x401fffff
[    0.169358] pci 0000:00:1c.0:   PREFETCH window: 0x00000040200000-0x000000403fffff
[    0.169365] pci 0000:00:1c.3: PCI bridge, secondary bus 0000:02
[    0.169369] pci 0000:00:1c.3:   IO window: 0xe000-0xefff
[    0.169374] pci 0000:00:1c.3:   MEM window: 0xfeb00000-0xfebfffff
[    0.169379] pci 0000:00:1c.3:   PREFETCH window: 0x00000040400000-0x000000405fffff
[    0.169386] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:03
[    0.169388] pci 0000:00:1e.0:   IO window: disabled
[    0.169393] pci 0000:00:1e.0:   MEM window: disabled
[    0.169397] pci 0000:00:1e.0:   PREFETCH window: disabled
[    0.169410] pci 0000:00:1c.0: enabling device (0104 -> 0107)
[    0.169418]   alloc irq_desc for 16 on node -1
[    0.169421]   alloc kstat_irqs on node -1
[    0.169428] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.169433] pci 0000:00:1c.0: setting latency timer to 64
[    0.169441]   alloc irq_desc for 19 on node -1
[    0.169443]   alloc kstat_irqs on node -1
[    0.169447] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[    0.169452] pci 0000:00:1c.3: setting latency timer to 64
[    0.169459] pci 0000:00:1e.0: setting latency timer to 64
[    0.169463] pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
[    0.169466] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[    0.169469] pci_bus 0000:01: resource 0 io:  [0x1000-0x1fff]
[    0.169472] pci_bus 0000:01: resource 1 mem: [0x40000000-0x401fffff]
[    0.169475] pci_bus 0000:01: resource 2 pref mem [0x40200000-0x403fffff]
[    0.169478] pci_bus 0000:02: resource 0 io:  [0xe000-0xefff]
[    0.169481] pci_bus 0000:02: resource 1 mem: [0xfeb00000-0xfebfffff]
[    0.169484] pci_bus 0000:02: resource 2 pref mem [0x40400000-0x405fffff]
[    0.169487] pci_bus 0000:03: resource 3 io:  [0x00-0xffff]
[    0.169489] pci_bus 0000:03: resource 4 mem: [0x000000-0xffffffff]
[    0.169525] NET: Registered protocol family 2
[    0.169621] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.169917] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.170553] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.170922] TCP: Hash tables configured (established 131072 bind 65536)
[    0.170926] TCP reno registered
[    0.171061] NET: Registered protocol family 1
[    0.171086] pci 0000:00:02.0: Boot video device
[    0.171397] cpufreq-nforce2: No nForce2 chipset.
[    0.171428] Scanning for low memory corruption every 60 seconds
[    0.171547] audit: initializing netlink socket (disabled)
[    0.171562] type=2000 audit(1279468868.167:1): initialized
[    0.182629] Trying to unpack rootfs image as initramfs...
[    0.196369] highmem bounce pool size: 64 pages
[    0.196376] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    0.197901] VFS: Disk quotas dquot_6.5.2
[    0.197967] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.204128] fuse init (API version 7.13)
[    0.204262] msgmni has been set to 1716
[    0.204544] alg: No test for stdrng (krng)
[    0.204618] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.204622] io scheduler noop registered
[    0.204624] io scheduler anticipatory registered
[    0.204626] io scheduler deadline registered
[    0.204668] io scheduler cfq registered (default)
[    0.204803]   alloc irq_desc for 24 on node -1
[    0.204806]   alloc kstat_irqs on node -1
[    0.204817] pcieport 0000:00:1c.0: irq 24 for MSI/MSI-X
[    0.204826] pcieport 0000:00:1c.0: setting latency timer to 64
[    0.204935]   alloc irq_desc for 25 on node -1
[    0.204937]   alloc kstat_irqs on node -1
[    0.204945] pcieport 0000:00:1c.3: irq 25 for MSI/MSI-X
[    0.204954] pcieport 0000:00:1c.3: setting latency timer to 64
[    0.205029] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.205112] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.205208] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[    0.205217] ACPI: Power Button [PWRB]
[    0.205265] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[    0.205268] ACPI: Power Button [PWRF]
[    0.205850] processor LNXCPU:00: registered as cooling_device0
[    0.216470] thermal LNXTHERM:01: registered as thermal_zone0
[    0.216481] ACPI: Thermal Zone [THRM] (40 C)
[    0.220396] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.220501] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    0.221121] 00:10: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    0.222175] brd: module loaded
[    0.222647] loop: module loaded
[    0.222747] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[    0.222864] ata_piix 0000:00:1f.1: version 2.13
[    0.222880]   alloc irq_desc for 18 on node -1
[    0.222882]   alloc kstat_irqs on node -1
[    0.222890] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    0.222927] ata_piix 0000:00:1f.1: setting latency timer to 64
[    0.223038] isapnp: Scanning for PnP cards...
[    0.232317] scsi0 : ata_piix
[    0.232470] scsi1 : ata_piix
[    0.233834] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[    0.233838] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[    0.233902] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    0.233907] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[    0.233948] ata_piix 0000:00:1f.2: setting latency timer to 64
[    0.234032] scsi2 : ata_piix
[    0.279772] scsi3 : ata_piix
[    0.279835] ata3: SATA max UDMA/133 cmd 0xd080 ctl 0xd000 bmdma 0xc800 irq 19
[    0.279838] ata4: SATA max UDMA/133 cmd 0xcc00 ctl 0xc880 bmdma 0xc808 irq 19
[    0.280229] Fixed MDIO Bus: probed
[    0.280266] PPP generic driver version 2.4.2
[    0.280335] tun: Universal TUN/TAP device driver, 1.6
[    0.280337] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.280437] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.280463]   alloc irq_desc for 23 on node -1
[    0.280465]   alloc kstat_irqs on node -1
[    0.280472] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    0.280490] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    0.280494] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    0.280537] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[    0.280557] ehci_hcd 0000:00:1d.7: using broken periodic workaround
[    0.280568] ehci_hcd 0000:00:1d.7: debug port 1
[    0.284447] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[    0.284495] ata2: port disabled. ignoring.
[    0.288291] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfea37c00
[    0.307976] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    0.308114] usb usb1: configuration #1 chosen from 1 choice
[    0.308149] hub 1-0:1.0: USB hub found
[    0.308159] hub 1-0:1.0: 8 ports detected
[    0.308230] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.308246] uhci_hcd: USB Universal Host Controller Interface driver
[    0.308295] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    0.308305] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    0.308309] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    0.308356] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    0.308385] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000d880
[    0.308485] usb usb2: configuration #1 chosen from 1 choice
[    0.308512] hub 2-0:1.0: USB hub found
[    0.308519] hub 2-0:1.0: 2 ports detected
[    0.308564] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    0.308571] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    0.308575] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    0.308621] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[    0.308646] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000d800
[    0.308742] usb usb3: configuration #1 chosen from 1 choice
[    0.308769] hub 3-0:1.0: USB hub found
[    0.308778] hub 3-0:1.0: 2 ports detected
[    0.308827] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    0.308834] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    0.308838] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    0.308880] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[    0.308915] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d480
[    0.309016] usb usb4: configuration #1 chosen from 1 choice
[    0.309043] hub 4-0:1.0: USB hub found
[    0.309050] hub 4-0:1.0: 2 ports detected
[    0.309094] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[    0.309100] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[    0.309104] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    0.309146] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[    0.309182] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000d400
[    0.309281] usb usb5: configuration #1 chosen from 1 choice
[    0.309309] hub 5-0:1.0: USB hub found
[    0.309316] hub 5-0:1.0: 2 ports detected
[    0.309432] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[    0.309781] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.309789] serio: i8042 AUX port at 0x60,0x64 irq 12
[    0.309934] mice: PS/2 mouse device common for all mice
[    0.310057] rtc_cmos 00:03: RTC can wake from S4
[    0.310106] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    0.310132] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[    0.310255] device-mapper: uevent: version 1.0.3
[    0.313111] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[    0.313958] device-mapper: multipath: version 1.1.0 loaded
[    0.313962] device-mapper: multipath round-robin: version 1.0.0 loaded
[    0.314937] EISA: Probing bus 0 at eisa.0
[    0.314944] Cannot allocate resource for EISA slot 1
[    0.314965] EISA: Detected 0 cards.
[    0.317448] cpuidle: using governor ladder
[    0.317451] cpuidle: using governor menu
[    0.317897] TCP cubic registered
[    0.318059] NET: Registered protocol family 10
[    0.318507] lo: Disabled Privacy Extensions
[    0.318791] NET: Registered protocol family 17
[    0.318855] Using IPI No-Shortcut mode
[    0.318954] PM: Resume from disk failed.
[    0.318966] registered taskstats version 1
[    0.319245]   Magic number: 2:18:35
[    0.319262] bdi 7:0: hash matches
[    0.319326] rtc_cmos 00:03: setting system clock to 2010-07-18 16:01:09 UTC (1279468869)
[    0.319329] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    0.319331] EDD information not available.
[    0.328605] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[    0.484498] ata3.00: ATA-7: SAMSUNG HD161HJ, JF100-19, max UDMA7
[    0.484503] ata3.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    0.484549] ata3.01: ATAPI: TSSTcorp CDDVDW SH-S203B, SB00, max UDMA/100
[    0.492304] ata3.00: configured for UDMA/133
[    0.508545] ata3.01: configured for UDMA/100
[    0.667459] Freeing initrd memory: 7782k freed
[    0.801474] isapnp: No Plug & Play device found
[    0.801667] scsi 2:0:0:0: Direct-Access     ATA      SAMSUNG HD161HJ  JF10 PQ: 0 ANSI: 5
[    0.801846] sd 2:0:0:0: Attached scsi generic sg0 type 0
[    0.802392] sd 2:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[    0.802469] sd 2:0:0:0: [sda] Write Protect is off
[    0.802474] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    0.802514] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    0.802713]  sda: sda1 sda2 sda3 <
[    0.812548] scsi 2:0:1:0: CD-ROM            TSSTcorp CDDVDW SH-S203B  SB00 PQ: 0 ANSI: 5
[    0.835489]  sda5 sda6 >
[    0.852947] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[    0.852953] Uniform CD-ROM driver Revision: 3.20
[    0.853088] sr 2:0:1:0: Attached scsi CD-ROM sr0
[    0.853171] sr 2:0:1:0: Attached scsi generic sg1 type 5
[    0.853329] sd 2:0:0:0: [sda] Attached SCSI disk
[    0.853342] Freeing unused kernel memory: 656k freed
[    0.853637] Write protecting the kernel text: 4676k
[    0.853664] Write protecting the kernel read-only data: 1840k
[    0.877730] udev: starting version 151
[    1.093999] Floppy drive(s): fd0 is 1.44M
[    1.111717] FDC 0 is a post-1991 82077
[    1.125884] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    1.125908] r8169 0000:02:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[    1.125954] r8169 0000:02:00.0: setting latency timer to 64
[    1.126014]   alloc irq_desc for 26 on node -1
[    1.126016]   alloc kstat_irqs on node -1
[    1.126032] r8169 0000:02:00.0: irq 26 for MSI/MSI-X
[    1.127186] eth0: RTL8101e at 0xf807e000, 00:1b:b9:90:ed:34, XID 14000000 IRQ 26
[    1.284326] EXT4-fs (sda6): mounted filesystem with ordered data mode
[   10.804962] Adding 999416k swap on /dev/sda5.  Priority:-1 extents:1 across:999416k
[   10.863046] udev: starting version 151
[   10.995646] lp: driver loaded but no devices found
[   11.074730] Linux agpgart interface v0.103
[   11.174080] intel_rng: FWH not detected
[   11.240348] agpgart-intel 0000:00:00.0: Intel 945G Chipset
[   11.240558] agpgart-intel 0000:00:00.0: detected 7932K stolen memory
[   11.242653] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[   11.351797] parport_pc 00:07: reported by Plug and Play ACPI
[   11.351863] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[   11.444346] lp0: using parport0 (interrupt-driven).
[   11.495499] [drm] Initialized drm 1.1.0 20060810
[   11.528231] psmouse serio1: ID: 10 00 64
[   11.529260] ppdev: user-space parallel port driver
[   11.573076] type=1505 audit(1279479680.752:2):  operation="profile_load" pid=511 name="/sbin/dhclient3"
[   11.573863] type=1505 audit(1279479680.752:3):  operation="profile_load" pid=511 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[   11.574278] type=1505 audit(1279479680.752:4):  operation="profile_load" pid=511 name="/usr/lib/connman/scripts/dhclient-script"
[   11.634073] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   11.634080] i915 0000:00:02.0: setting latency timer to 64
[   11.656088] [drm] set up 7M of stolen space
[   11.657295] [drm] initialized overlay support
[   12.077626] input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input4
[   12.155911] type=1505 audit(1279479681.332:5):  operation="profile_load" pid=676 name="/usr/share/gdm/guest-session/Xsession"
[   12.173552] type=1505 audit(1279479681.352:6):  operation="profile_replace" pid=679 name="/sbin/dhclient3"
[   12.174330] type=1505 audit(1279479681.352:7):  operation="profile_replace" pid=679 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[   12.174745] type=1505 audit(1279479681.352:8):  operation="profile_replace" pid=679 name="/usr/lib/connman/scripts/dhclient-script"
[   12.194809] r8169: eth0: link up
[   12.194818] r8169: eth0: link up
[   12.200696] type=1505 audit(1279479681.380:9):  operation="profile_load" pid=680 name="/usr/bin/evince"
[   12.207951] fb0: inteldrmfb frame buffer device
[   12.207955] registered panic notifier
[   12.207965] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[   12.208032] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   12.208060] HDA Intel 0000:00:1b.0: setting latency timer to 64
[   12.222459] vga16fb: initializing
[   12.222464] vga16fb: mapped to 0xc00a0000
[   12.222469] vga16fb: not registering due to another framebuffer present
[   12.298714] type=1505 audit(1279479681.476:10):  operation="profile_load" pid=680 name="/usr/bin/evince-previewer"
[   12.349738] type=1505 audit(1279479681.528:11):  operation="profile_load" pid=680 name="/usr/bin/evince-thumbnailer"
[   12.387725] Console: switching to colour frame buffer device 128x48
[   12.401106] input: HDA Intel Line In at Ext Rear Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input5
[   12.401435] input: HDA Intel Mic at Ext Front Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6
[   12.401763] input: HDA Intel Mic at Ext Rear Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[   12.402386] input: HDA Intel Speaker at Ext Rear Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[   12.402715] input: HDA Intel HP Out at Ext Front Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[   12.861536] RPC: Registered udp transport module.
[   12.861540] RPC: Registered tcp transport module.
[   12.861542] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   12.924974] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   13.010428] svc: failed to register lockdv1 RPC service (errno 97).
[   13.012698] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[   13.022670] NFSD: starting 90-second grace period
[   16.928037] end_request: I/O error, dev fd0, sector 0
[   16.964039] end_request: I/O error, dev fd0, sector 0
[   22.636027] eth0: no IPv6 routers present
En línea

Páginas: [1] 2 3 4 5 Ir Arriba Respuesta Imprimir 

Ir a:  

Mensajes similares
Asunto Iniciado por Respuestas Vistas Último mensaje
Efectos visuales
Programación C/C++
dnsdirm 1 4,005 Último mensaje 6 Mayo 2011, 09:02 am
por Slava_TZD
¿Duda cuantos efectos visuales de interfas existe en Linux?
GNU/Linux
bacanzito 0 1,490 Último mensaje 26 Agosto 2013, 15:57 pm
por bacanzito
WAP2 - Aviso Legal - Powered by SMF 1.1.21 | SMF © 2006-2008, Simple Machines