Ya se que no han dado los mejores resultados pero quería mas bien probar y sino tengo un amigo que me lo va a comprar de todas todas.
Mi pregunta es ahora que a que adaptadores puedo acoplárselo... porque como a mi GOLD 500 le meta el apli de 1W :S:S me da a mi que explota!!
Pues lo dicho, que requerimientos tengo que buscar en un adaptador para que puea soportar el watio del apli??
Indicaciones del ampli:
Citar
Works with an indoor Wireless WiFi Access Point to improve its operation WiFi range and performance! The WiFi Signal Booster can increase the effective range and coverage area of the network.
Ideal for use with WiFi 2.4 GHz frequency hopping or direct sequence spread spectrum radio modems and 11 mbps IEEE802.11b devices. The booster increases range by providing transmit booster gain as well as low-noise receive gain. This receive booster gain increases the receive sensitivity of wireless LAN WiFi Access Point.
* Maximum output power of 1000mW by the WiFi Wireless Booster!
* WiFi Wireless Booster Use die Casting Aluminium for better heat exchange
* Signal activity LED
* High Gain WiFi Signal, High Value , High Performance
* Low-noise receive gain
* Designed for 2.4GHz WiFi Wireless LANs
* Plug-and-play, Easy installation, no driver needed for the WiFi Wireless Booster
* Brand NEW WiFi Wireless Booster
* NOTE: Antenna and Access Point Router are NOT included
* Electricial Specification:
Wireless Operation Range: 2400-2500 MHz
Operation WiFi Mode: Bi-directional, half-duplex, Auto-Switching via carrier sensing
Frequency Response: ± 1dB over operation range
Amplifier Input Power: 6dBm (Min.) , 20dBm (Max.)
Amplifier Output Power: 1000mW/30dBm nominal for WiFi 802.11b/11Mbps
Amplifier Connector: SMA Receptacle, 50 ohm
Transmit Booster Gain: 17dBm nominal
Receiver Booster Gain: 10dBm
Receive Noise Figure: 3.5dBm nominal
* WiFi Wireless Booster Mechanical Specification:
Operationg Temperature: 20 to 70 degree
Operating Humidity: Up to 95% relative humidity
Dimesnion: 7.8 cm (L) x 5.6 cm (W) x 2.9 cm (H)
Material: Die Casting Aluminum
Safety Certification: FCC/CE/VCC
Ideal for use with WiFi 2.4 GHz frequency hopping or direct sequence spread spectrum radio modems and 11 mbps IEEE802.11b devices. The booster increases range by providing transmit booster gain as well as low-noise receive gain. This receive booster gain increases the receive sensitivity of wireless LAN WiFi Access Point.
* Maximum output power of 1000mW by the WiFi Wireless Booster!
* WiFi Wireless Booster Use die Casting Aluminium for better heat exchange
* Signal activity LED
* High Gain WiFi Signal, High Value , High Performance
* Low-noise receive gain
* Designed for 2.4GHz WiFi Wireless LANs
* Plug-and-play, Easy installation, no driver needed for the WiFi Wireless Booster
* Brand NEW WiFi Wireless Booster
* NOTE: Antenna and Access Point Router are NOT included
* Electricial Specification:
Wireless Operation Range: 2400-2500 MHz
Operation WiFi Mode: Bi-directional, half-duplex, Auto-Switching via carrier sensing
Frequency Response: ± 1dB over operation range
Amplifier Input Power: 6dBm (Min.) , 20dBm (Max.)
Amplifier Output Power: 1000mW/30dBm nominal for WiFi 802.11b/11Mbps
Amplifier Connector: SMA Receptacle, 50 ohm
Transmit Booster Gain: 17dBm nominal
Receiver Booster Gain: 10dBm
Receive Noise Figure: 3.5dBm nominal
* WiFi Wireless Booster Mechanical Specification:
Operationg Temperature: 20 to 70 degree
Operating Humidity: Up to 95% relative humidity
Dimesnion: 7.8 cm (L) x 5.6 cm (W) x 2.9 cm (H)
Material: Die Casting Aluminum
Safety Certification: FCC/CE/VCC
Gracias!!!!