Hola, acabo de instalar bugtraq en mi netbook, pero resulta que no tengo conexion inalambrica!!
A mi se me ocurrio pensar que podia ser por los drivers, asique fui a la pagina de realtek y busque mi tarjeta de red, descargue el driver en formato tar.bz2...
pero no se que hacer con esto, he leido algo en internet sobre descomprimirlo y en la carpeta creada hacer ./configure , make , make install pero no puedo porque el ./configure me da error ( pone "bash: ./configure: No such file or directory")
asique no puedo seguir con make o make install
Mi tarjeta es una Realtek RTL8188CE

Hola, gracias por tu respuesta
Cuando abro la carpeta con el explorador de archivos, no aparece nada llamado "configure"
por si sirve esto es lo que me da cuando pongo "ls"

base.c                              core.c    pci.c   release_note
base.h                              core.h    pci.h   rtl8188ee
cam.c                               debug.c   ps.c    rtl8192ce
cam.h                               debug.h   ps.h    rtl8192de
compat                              efuse.c   rc.c    rtl8192se
compat.h                            efuse.h   rc.h    rtl8723e
compat-wireless-3.0-2-mesh.tar.bz2  firmware  readme  stats.c
compat-wireless-3.0-2.tar.bz2       Kconfig   regd.c  stats.h
compat-wireless-3.2.5-1.tar.bz2     Makefile  regd.h  wifi.h

Hola, con este driver avance algo mas que con el otro
pero sigo teniendo un problema:
esto fue lo que yo hice
root@ubuntu:/home/bugtraq/Downloads/rtl8188ce-linux-driver-master# make
if [ -e verify_branch.sh ] ; \
   then \
       ./verify_branch.sh ; \
   fi;
Verifying a sane branch for your kernel version...
No (current branch rtl8188ce-linux-driver-master)
-e
You don't appear to be in a Git checkout.
This means branch information is not available.
You can still proceed to build, but you might be using unstable code.
Would you like me to try and get a git checkout for you? (Y/N): y
Reading package lists... Done
Building dependency tree       
Reading state information... Done
gcc is already the newest version.
build-essential is already the newest version.
linux-headers-generic is already the newest version.
0 upgraded, 0 newly installed, 0 to remove and 770 not upgraded.
Reading package lists... Done
Building dependency tree       
Reading state information... Done
git is already the newest version.
0 upgraded, 0 newly installed, 0 to remove and 770 not upgraded.
Cloning into 'rtl8188ce-linux-driver'...
remote: Counting objects: 4528, done.
remote: Total 4528 (delta 0), reused 0 (delta 0)
Receiving objects: 100% (4528/4528), 16.28 MiB | 293 KiB/s, done.
Resolving deltas: 100% (3462/3462), done.
-e
Looks like the clone was successful (new folder is /home/bugtraq/Downloads/rtl8188ce-linux-driver-master/rtl8188ce-linux-driver)
-e Kicking off the build...

make[1]: Entering directory `/home/bugtraq/Downloads/rtl8188ce-linux-driver-master/rtl8188ce-linux-driver'
if [ -e verify_branch.sh ] ; \
   then \
       ./verify_branch.sh ; \
   fi;
Verifying a sane branch for your kernel version...
No (Current branch  master)
Recommended branch is ubuntu-12.04 based on your kernel version (3.2.0-40-generic)
Should I switch it to ubuntu-12.04 for you?  (y/n): n
OK, but if the build fails come back here and try again.
Continue with the build? (Y/N): y
make -C /lib/modules/3.2.0-40-generic/build M=/home/bugtraq/Downloads/rtl8188ce-linux-driver-master/rtl8188ce-linux-driver modules
make[2]: Entering directory `/lib/modules/3.2.0-40-generic/build'
make[2]: *** No rule to make target `modules'.  Stop.
make[2]: Leaving directory `/lib/modules/3.2.0-40-generic/build'
make[1]: *** [all] Error 2
make[1]: Leaving directory `/home/bugtraq/Downloads/rtl8188ce-linux-driver-master/rtl8188ce-linux-driver'
./verify_branch.sh: 121: ./verify_branch.sh: 2: not found
-e
Build exited with failure status (Exit code 127).
To install, cd over to rtl8188ce-linux-driver and run "sudo make install"
make -C /lib/modules/3.2.0-40-generic/build M=/home/bugtraq/Downloads/rtl8188ce-linux-driver-master modules
make[1]: Entering directory `/lib/modules/3.2.0-40-generic/build'
make[1]: *** No rule to make target `modules'.  Stop.
make[1]: Leaving directory `/lib/modules/3.2.0-40-generic/build'
make: *** [all] Error 2

Gracias por tu respuesta 
Puse ese comando y al final me dice esto:
Error! Could not locate dkms.conf file.
File:  does not exist.
Error! Your kernel headers for kernel 3.2.0-40-generic cannot be found.
Please install the linux-headers-3.2.0-40-generic package,
or use the --kernelsourcedir option to tell DKMS where it's located

Puse ese ultimo comando, espere a que termine y reinicie, cuando pongo "sudo apt-get install linux-headers-3.2.0-40-generic" me sale esto:
Reading package lists... Done
Building dependency tree       
Reading state information... Done
linux-headers-3.2.0-40-generic is already the newest version.
0 upgraded, 0 newly installed, 0 to remove and 770 not upgraded.

pero sigo sin poder hacer make ni ./confgiure