Título: Mi makina no detecta temperaturas Publicado por: unusuario en 8 Octubre 2014, 13:30 pm Saludos,mi makina: pentium 4,cpu 3,Board: Gigabyte Technology Co., Ltd. GA-8S648FX.estoy intentando visualizar las temperaturas de mi makina,pero solo puedo ver las del HDD con HDDTEMP,ya que LM-SENSORS dice (No sensors found! Make sure you loaded all the kernel drivers you need.Try sensors-detect to find out which these are) Sigo todos los pasos al pie de la letra como dicen los tutoriales,pero nada no hay manera. 1 - sudo apt-get install lm-sensors 2 - sudo sensors-detect,a todos los pasos (yes),solo me detecta el modulo (it87) resultado de sensors-detect: ----------------------------------------------------------------------------- # sensors-detect revision 5984 (2011-07-10 21:22:53 +0200) # Board: Gigabyte Technology Co., Ltd. GA-8S648FX This program will help you determine which kernel modules you need to load to use lm_sensors most effectively. It is generally safe and recommended to accept the default answers to all questions, unless you know what you're doing. Some south bridges, CPUs or memory controllers contain embedded sensors. Do you want to scan for them? This is totally safe. (YES/no): y Silicon Integrated Systems SIS5595... No VIA VT82C686 Integrated Sensors... No VIA VT8231 Integrated Sensors... No AMD K8 thermal sensors... No AMD Family 10h thermal sensors... No AMD Family 11h thermal sensors... No AMD Family 12h and 14h thermal sensors... No AMD Family 15h thermal sensors... No AMD Family 15h power sensors... No Intel digital thermal sensor... No Intel AMB FB-DIMM thermal sensor... No VIA C7 thermal sensor... No VIA Nano thermal sensor... No Some Super I/O chips contain embedded sensors. We have to write to standard I/O ports to probe them. This is usually safe. Do you want to scan for Super I/O sensors? (YES/no): y Probing for Super-I/O at 0x2e/0x2f Trying family `National Semiconductor/ITE'... No Trying family `SMSC'... No Trying family `VIA/Winbond/Nuvoton/Fintek'... No Trying family `ITE'... Yes Found `ITE IT8705F Super IO Sensors' Success! (address 0x290, driver `it87') Probing for Super-I/O at 0x4e/0x4f Trying family `National Semiconductor/ITE'... No Trying family `SMSC'... No Trying family `VIA/Winbond/Nuvoton/Fintek'... No Trying family `ITE'... Yes Found `ITE IT8705F Super IO Sensors' Success! (address 0x290, driver `it87') Some systems (mainly servers) implement IPMI, a set of common interfaces through which system health data may be retrieved, amongst other things. We first try to get the information from SMBIOS. If we don't find it there, we have to read from arbitrary I/O ports to probe for such interfaces. This is normally safe. Do you want to scan for IPMI interfaces? (YES/no): y Probing for `IPMI BMC KCS' at 0xca0... No Probing for `IPMI BMC SMIC' at 0xca8... No Some hardware monitoring chips are accessible through the ISA I/O ports. We have to write to arbitrary I/O ports to probe them. This is usually safe though. Yes, you do have ISA I/O ports even if you do not have any ISA slots! Do you want to scan the ISA I/O ports? (yes/NO): y Probing for `National Semiconductor LM78' at 0x290... No Probing for `National Semiconductor LM79' at 0x290... No Probing for `Winbond W83781D' at 0x290... No Probing for `Winbond W83782D' at 0x290... No Lastly, we can probe the I2C/SMBus adapters for connected hardware monitoring devices. This is the most risky part, and while it works reasonably well on most systems, it has been reported to cause trouble on some systems. Do you want to probe the I2C/SMBus adapters now? (YES/no): y Using driver `i2c-sis96x' for device 0000:00:02.1: Silicon Integrated Systems SMBus Controller Module i2c-dev loaded successfully. Next adapter: SiS96x SMBus adapter at 0x1400 (i2c-0) Do you want to scan it? (yes/NO/selectively): y Client found at address 0x50 Probing for `Analog Devices ADM1033'... No Probing for `Analog Devices ADM1034'... No Probing for `SPD EEPROM'... Yes (confidence 8, not a hardware monitoring chip) Probing for `EDID EEPROM'... No Client found at address 0x51 Probing for `Analog Devices ADM1033'... No Probing for `Analog Devices ADM1034'... No Probing for `SPD EEPROM'... Yes (confidence 8, not a hardware monitoring chip) Now follows a summary of the probes I have just done. Just press ENTER to continue: Driver `it87': * ISA bus, address 0x290 Chip `ITE IT8705F Super IO Sensors' (confidence: 9) To load everything that is needed, add this to /etc/modules: #----cut here---- # Chip drivers it87 #----cut here---- If you have some drivers built into your kernel, the list above will contain too many modules. Skip the appropriate ones! Do you want to add these lines automatically to /etc/modules? (yes/NO) ------------------------------------------------------------------------------ tambien e intentado cargar el modulo (it87) con modprobe (sudo modprobe it87),pero da este error (FATAL: Error inserting it87 (/lib/modules/3.8.0-44-generic/kernel/drivers/hwmon/it87.ko): Device or resource busy),ya no se que hacer,me faltan conocimientos,por ello recurro a quien sepa mas que yo,es mi ultimo recurso,ya que no me gusta molestar. sin embargo se que se pueden visualizar las temperaturas porque desde la BIOS,se pueden ver todas,no comprendo porque desde ubuntu no puedo,ya que e probado casi todos los tutoriales que me e encontrado. solicito info,gracias Título: Re: Mi makina no detecta temperaturas Publicado por: MinusFour en 9 Octubre 2014, 16:07 pm Cuando te pregunto:
Código: Do you want to add these lines automatically to /etc/modules? (yes/NO) żLe dijiste que no? Título: Re: Mi makina no detecta temperaturas Publicado por: unusuario en 21 Octubre 2014, 21:59 pm Gracias por el interes,e probado con si y con no,e instalando los modulos manualmente,tambien e probado todo lo que me e encontrado por la red,ya estoy aburrido de probar cosas y no encontrar resultados,creo q voy a abandonar en mi makina este problema no tiene solucion,lo que mas me fastidia es que desde la bios si visualizo las temp.,los voltajes
Título: Re: Mi makina no detecta temperaturas Publicado por: MinusFour en 22 Octubre 2014, 18:00 pm Cuando haces el modprobe, "dmesg" te arroja esto?
Código: ACPI: I/O resource it87 [0x295-0x296] conflicts with ACPI region IP__ Si te arroja eso tienes que cargar una linea especial en el archivo de grub: acpi_enforce_resources=lax http://www.lm-sensors.org/wiki/FAQ/Chapter3#Mysensorshavestoppedworkinginkernel2.6.31 |